Interchangeable Lens Digital Camera ILCE-7RM2

TC/UB Settings

The time code (TC) and the user bit (UB) information can be recorded as data attached to movies.

  1. MENU → (Setup) → [TC/UB Settings] → setting value you want to change.

Menu item details

TC/UB Disp. Setting:
Sets the display for the counter, time code, and user bit.
TC Preset:
Sets the time code.
UB Preset:
Sets the user bit.
TC Format:
Sets the recording method for the time code. (Only when [NTSC/PAL Selector] is set to NTSC.)
TC Run:
Sets the count up format for the time code.
TC Make:
Sets the recording format for the time code on the recording medium.
UB Time Rec:
Sets whether or not to record the time as a user bit.

How to set the time code (TC Preset)

  1. MENU → (Setup) → [TC/UB Settings] [TC Preset], then press in the center of the control wheel.
  2. Turn the control wheel and select the first two digits.
    • The time code can be set between the following range.
      When [60i] is selected: 00:00:00:00 to 23:59:59:29
      *When [24p] is selected, you can select the last two digits of the time code in multiples of four from 0 to 23 frames.
      When [50i] is selected: 00:00:00:00 to 23:59:59:24
  3. Set the other digits following the same procedure as in step 2, then press in the center of the control wheel.

How to reset the time code

  1. MENU → (Setup) → [TC/UB Settings] [TC Preset], then press in the center of the control wheel.
  2. Press the (Delete) button to reset the time code (00:00:00:00).

You can also reset the time code (00:00:00:00) using the RMT-VP1K remote commander (sold separately).

How to set the user bit (UB Preset)

  1. MENU → (Setup) → [TC/UB Settings] [UB Preset], then press in the center of the control wheel.
  2. Turn the control wheel and select the first two digits.
  3. Set the other digits following the same procedure as in step 2, then press in the center of the control wheel.

How to reset the user bit

  1. MENU → (Setup) → [TC/UB Settings] [UB Preset], then press in the center of the control wheel.
  2. Press the (Delete) button to reset the user bit (00 00 00 00).

How to select the recording method for the time code (TC Format*1)

  1. MENU → (Setup) → [TC/UB Settings] [TC Format], then press in the center of the control wheel.
DF:
Records the time code in Drop Frame*2 format.
NDF:
Records the time code in Non-Drop Frame format.

*1 Only when [NTSC/PAL Selector] is set to NTSC.

*2 The time code is based on 30 frames per second. However, a gap between the actual time and the time code will occur during extended periods of recording as the frame frequency of the NTSC image signal is approximately 29.97 frames per second. Drop frame corrects this gap to make the time code and actual time equal. In drop frame, the first 2 frame numbers are removed every minute except for every tenth minute. The time code without this correction is called non-drop frame.

  • The setting is fixed to [NDF] when recording in 4K/24p or 1080/24p.

How to select the count up format for the time code (TC Run)

  1. MENU → (Setup) → [TC/UB Settings] [TC Run], then press in the center of the control wheel.
Rec Run:
Sets the stepping mode for the time code to advance only while recording. The time code is recorded sequentially from the last time code of the previous recording.
Free Run:
Sets the stepping mode for the time code to advance anytime, regardless of the camera operation.

  • The time code may not be recorded sequentially in the following situations even when the time code advances in [Rec Run] mode.
    • When the recording format is changed.
    • When the recording medium is removed.

How to select how the time code is recorded (TC Make)

  1. MENU → (Setup) → [TC/UB Settings] [TC Make], then press in the center of the control wheel.
Preset:
Records the newly set time code on the recording medium.
Regenerate:
Reads the last time code for the previous recording from the recording medium and records the new time code consecutively from the last time code. The time code advances in [Rec Run] mode regardless of the [TC Run] setting.