Specifications
Sound Bar (YY2099C)
Front speaker section
Speaker
45 mm × 108 mm (1 13/16 in × 4 3/8 in) cone type (2)
Speaker system
Passive radiator type
Front tweeter section
Speaker
16 mm (21/32 in) dome type (2)
Center speaker section
Speaker
46 mm × 54 mm (1 13/16 in × 2 1/4 in) cone type (1)
Speaker system
Acoustic suspension type
Top speaker section
Speaker
46 mm × 54 mm (1 13/16 in × 2 1/4 in) cone type (2)
Speaker system
Acoustic suspension type
Side speaker section
Speaker
46 mm × 54 mm (1 13/16 in × 2 1/4 in) cone type (2)
Speaker system
Acoustic suspension type
Wireless LAN section
Communication system
IEEE 802.11 a/b/g/n/ac/ax
BLUETOOTH section
Output
BLUETOOTH Specification Power Class 1.5
Maximum communication range
Line of sight approx. 30 m (98.4 ft)*
* The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone use, reception sensitivity, the operating system, software applications, etc.
Frequency band
2.4 GHz band (2.400 0 GHz - 2.483 5 GHz)
Modulation method
FHSS
Compatible BLUETOOTH profile*
* A BLUETOOTH profile standardizes functions according to the characteristics of BLUETOOTH devices.
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio Video Remote Control Profile)
Supported codec*
* Codec is an audio signal compression and conversion format.
SBC (Subband Codec)
AAC (Advanced Audio Coding)
LDAC™*
* LDAC is an audio coding technology developed by Sony that enables the transmission of High-Resolution (Hi-Res) Audio content, even over a BLUETOOTH connection.
Corresponding content protection
SCMS-T
Transmission range (A2DP)
20 Hz - 20 000 Hz (Sampling frequency 44.1 kHz)
20 Hz - 40 000 Hz (Sampling frequency LDAC 96 kHz, 990 kbps transmission)
Note
- Depending on the network environment, there may be an interruption at the high bitrate transmission.
USB section (For service use only)
FOR SERVICE port
Type A (For connecting USB memory)
HDMI section
Connector
Type A (19pin)
Wireless transmitter/receiver section
Communication system
Wireless Sound Specification
Modulation method
OFDM
General
Input
HDMI IN
Output
HDMI OUT (TV (eARC/ARC))
Power consumption
On: 52 W
Network standby mode ([Network/Bluetooth Standby] is set to ON): 3.5 W or less
Standby mode ([Network/Bluetooth Standby] is set to OFF): 0.5 W or less*
* When [Signal Pass Through] is set to [Off], or when [Signal Pass Through] is set to [Auto] and the connected TV is turned off.
* Changing the settings of the unit as described below will cause the power consumption to exceed the value listed above.
- Set [Signal Pass Through] to [On]
- Set [Signal Pass Through] to [Auto] and [Control for HDMI] to [Off]
When the [Auto Standby] function is enabled, if the product is not being operated and there is no signal input for about 20 minutes, the speaker system automatically enters the network standby mode or standby mode.
Disabling the [Auto Standby] function will increase the power consumption of this product.
Dimensions* (W × H × D)
* Not including projection portion.
Approx. 950 mm × 64 mm × 125 mm (37 1/2 in × 2 5/8 in × 5 in)
Sound Bar with the Wall mounting bracket:Approx. 950 mm × 66 mm × 135 mm (37 1/2 in × 2 5/8 in × 5 3/8 in)
Sound Bar with the Foot:Approx. 950 mm × 74 mm × 125 mm (37 1/2 in × 3 in × 5 in)
Mass
Sound Bar:
Approx. 4.6 kg (10 lb 3 oz)
Sound Bar with the Wall mounting bracket:
Approx. 4.9 kg (10 lb 13 oz)
Sound Bar with the Foot:
Approx. 4.6 kg (10 lb 3 oz)
Note
- Design and specifications are subject to change without notice.
- Refer to the Reference Guide included with your product, which may contain specification information not listed above.