General Setup (GENERAL)

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].


CLOCK (clock)

Sets the clock: [AUTO <RDS>], [MANUAL].


BEEP (beep)

Activates the beep sound: [ON], [OFF].


AUTO OFF (auto off)

Shuts off automatically after a certain time when the unit is turned off and the clock is displayed (i.e. press and hold OFF for 1 second): [ENABLE] (30 minutes), [DISABLE].


STEERING (steering)

Registers/resets the setting of the steering wheel remote control. (Available only while the source is off and the clock is displayed.)

Item Detail
STRG CTRL
(steering control) 		Selects the input mode of the connected remote control. To prevent a malfunction, be sure to match the input mode with the connected remote control before use.
[CUSTOM] (custom)
Input mode for the steering wheel remote control.
[PRESET] (preset)
Input mode for the wired remote control excluding the steering wheel remote control. (Automatically selected when [RESETCUSTOM] is performed.)
EDIT CUSTOM
(edit custom) 		Registers the functions (SOURCE, ATT (attenuate), VOL (volume) +/–, SEEK +/–, VOICE, ON HOOK, OFF HOOK) to the steering wheel remote control:
Rotate the control dial to select the function you want to assign to the steering wheel remote control, then press it.
While [REGISTER] is blinking, press and hold the button on the steering wheel remote control you want to assign the function to. When registration is complete, [REGISTERED] is displayed.
To register other functions, repeat steps and .
(Available only when [STRG CTRL] is set to [CUSTOM].)
RESETCUSTOM
(reset custom) 		Resets the registered functions of the steering wheel remote control: [YES], [NO].
(Available only when [STRG CTRL] is set to [CUSTOM].)

Note

  • While making settings, only button operation on the unit is available. For safety, park your car before making this setting.
  • If an error occurs while registering, all the previously-registered information remains. Restart registration from the function where the error occurred.
  • This function may not be available on some vehicles. For details on the compatibility of your vehicle, visit the support site.


SPKR LOAD (speaker impedance load)

Sets the impedance load of the speaker connection: [4 OHM] (4 Ω load connection), [2 OHM] (2 Ω load connection).
(Available only while the source is off and the clock is displayed.)

  • Set to [2 OHM] when connecting as follows:
    - When connecting front speakers in parallel.
    - When connecting subwoofer(s) to right and left rear speaker leads.
    - When connecting a dual voice coil subwoofer with 4 Ω to 8 Ω impedance.


USB AUTOPLY (USB auto play)

Activates the USB auto play: [ON], [OFF].



USB MODE (USB mode)

Changes the USB mode: [ANDROID], [MSC/MTP].
(Available only when the USB is selected.)



BTM (best tuning memory)

Presets stations automatically.
(Available only when the radio is selected.)


PARENTAL (SiriusXM parental)

Sets the parental lock to [ON], [OFF], and edits the passcode.
(Available only when SiriusXM is selected.)


SXM SIGNAL (SiriusXM signal)

Displays the current status of the SiriusXM signal strength: [NO SIGNAL] (signal level 0), [WEAK] (signal level 1), [GOOD] (signal level 2), [EXCELLENT] (signal level 3).
(Available only when SiriusXM is selected.)


SXM RESET (SiriusXM reset)

Initializes the SiriusXM Connect Vehicle Tuner settings (preset channels/parental lock): [YES], [NO].
(Available only when SiriusXM is selected.)


INITIALIZE (initialize)

Initializes all the settings to the factory settings: [YES], [NO].
(Available only while the source is off and the clock is displayed.)


FIRMWARE (firmware)

(Available only while the source is off and the clock is displayed.)
Checks/updates the firmware version. For details, visit the support site.

Item Detail
FW VERSION
(firmware version) 		Displays current firmware version.
FW UPDATE
(firmware update) 		Enters firmware update process: [YES], [NO].
Updating the firmware takes a few minutes to complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device.
Go to Page Top