Copying the Projector Settings and Downloading to Other Projectors

You can copy the projector settings to a USB drive and download them to other projectors.

This function can be used when applying the same settings to multiple projectors of the same model.

Note

  • This projector has been confirmed to be compatible with USB 2.0 drives with capacities of up to 8 GB. However, it is not guaranteed to work with all USB drives.
    If formatting your USB drive, be sure that the file system is set to FAT32. Formatting with any other type of file system will make the drive incompatible with the projector.
  • Use an empty USB drive with no files or folders stored on it. If there are any files or folders stored on the USB drive, delete them before use.
  • If the USB drive you are using has projector setting data, copying of the settings will not start.
  • If the firmware versions of the copy source projectors and download destination projectors are different, the settings copied cannot be downloaded.
  1. Turn off the power of the copy source projector, then unplug the AC power cord.
  2. Insert the USB drive into the USB terminal of the copy source projector.
  3. Plug the AC power cord to the wall outlet while pressing and holding (Up) of the ENTER (Enter)/ / / / (Arrow) key on the copy source projector.

    Press and hold (Up) until the ON/STANDBY indicator flashes in orange.

  4. When the ON/STANDBY indicator starts flashing in orange, release (Up).

    When copying of the settings is complete, the ON/STANDBY indicator is lit in red.

  5. Remove the USB drive from the copy source projector.
  6. Turn off the power of the download destination projector, then unplug the AC power cord.
  7. Insert the USB drive with the settings copied into the USB terminal of the download destination projector.
  8. Plug the AC power cord to the wall outlet while pressing and holding (Down) of the ENTER (Enter)/ / / / (Arrow) key on the download destination projector.

    Press and hold (Down) until the ON/STANDBY indicator flashes in orange.

  9. When the ON/STANDBY indicator starts flashing in orange, release (Down).

    When downloading of the settings is complete, the ON/STANDBY indicator is lit in red.

  10. Remove the USB drive from the download destination projector.

Settings that can be copied/downloaded

OSD menu

Projection Setting

  • Intelligent Setting
  • Picture Mode
  • Contrast
  • Brightness
  • Color
  • Hue
  • Color Temp.
  • Sharpness
  • Light Settings
    • Dynamic Control
    • Light Output Mode
    • Light Out Control
  • Expert Setting
    • Ambiance
    • Reality Creation
    • Bright View
    • Gamma Mode
    • Color Space
    • Color Correction

Screen

  • Aspect
  • Overscan

Function

  • Audio Output Vol.
  • Smart APA
  • CC Display
  • Background
  • Start Up Image

Operation

  • Language
  • Menu Position
  • Status
  • IR Receiver
  • ID Mode

Connection/Power

  • Network Setting
    • Communication Mode
  • HDBaseT Settings
    • LAN Setting
    • RS-232C Setting
    • Extron XTP
  • Dynamic Range
    • Input-B
    • Input-C
    • Input-D
  • HDMI Cable
  • Input-A Signal Sel.
  • ECO
    • With No Input and With Static Signal of Auto Power Saving
    • Standby Mode
    • Remote Start
  • Auto Input Select
  • Auto Power On
  • Direct Power On

Installation

  • Image Flip
  • High Altitude Mode
  • Screen Aspect

WEB menu (supported on version 1.04 or later)

Setting

  • Setting
    • Timezone
    • Use NTP sever
      - NTP Server
    • Manual(Local)
      - Date(yyyy-mm-dd)
      - Time(hh:mm:ss)

E-mail Report

  • E-mail Report
    • Send To
    • CC
    • Report Timing
  • E-mail Account
    • User Name
    • Password
    • SMTP Server

ADCP

  • ADCP
    • Start ADCP Service
    • Requires Authentification
    • Port No.
    • Timeout
    • Host Address
      - Address list

Advertisement/PJ Talk/PJ Link

  • Advertisement
    • Start Advertisement Service
    • Community
    • Port No.
    • Interval
    • Broadcast Address
      - Address list
  • PJ Link
    • Start PJ Link Service
    • Requires Authentification
  • PJ Talk
    • Start PJ Talk Service
    • Community
    • Port No.
    • Timeout
    • Host Address
      - Address list

DDDP/Crestron Control

  • DDDP
    • Start DDDP Service
  • Crestron Control
    • Start Crestron Service
    • IP Address
    • IP ID(HEX)
    • Port No.

Certificate

  • Communication Mode

SNMP

  • SNMP
    • Start SNMP Service
    • Community
    • Community name
    • Rights
    • Trap destinations
      - Address list
    • Accept SNMP packets from any host
    • Accept SNMP packets from these hosts
      - Address list

Hint

  • It takes about 30 seconds to start copying/downloading the settings.
  • It takes about 2 minutes to complete copying the settings.
  • It takes about 10 minutes to complete downloading the settings.
  • After copying/downloading the settings, [Standby Mode] of the power supply is set to [Low].
Go to Page Top