Maintenance

Perform regular maintenance by following the procedures below.

  1. Remove the earbud tip.

    Hold the headset unit and twist the earbud tip while rotating it to pull it out.

    Do not pinch the end of the earbud tip when removing it.

    Illustration of removing the earbud tip while rotating it away from the headset unit

  2. Clean the headset.

    Cleaning the headset units

    When the headset exterior is dirty, wipe it clean with a soft dry cloth. If the headset is particularly dirty, soak a cloth in diluted neutral detergent, and wring it well before using it to clean the headset. Do not use solvents such as alcohol, thinner, or benzene, as they may damage the finish on the surface of the headset or cause other damages.

    Use a soft dry cloth to wipe off any water that gets on the headset units.

    Do not allow the headset to remain with water droplets attached in a cold environment as the water may freeze.

    Cleaning the microphone parts

    Wipe off any dirt on the mesh part of the headset unit with a cloth that has been moistened with water and wrung out tightly.

    Remove the dirt so that it does not push into the mesh part of the headset unit deeply.

    Cleaning the IR sensors

    If the IR sensors are dirty, wearing of the headset may not be detected and the headset may not work properly.

    Wipe off any dirt on the IR sensors with a soft dry cloth, etc.

    Illustration indicating the locations of the IR sensors (A) on the left and right headset units

    A: IR sensors (left, right)

    Cleaning the charging ports

    If foreign matter or moisture, such as sweat, etc., is left on the charging ports of the headset units or charging case, charging port corrosion may occur and prevent charging.

    When you have finished using the headset, make sure to gently clean the charging ports with a soft dry cloth or cotton swab.

    When the headset cannot be charged, it may help to try thoroughly cleaning the charging ports.


    Charging ports that needs maintenance

    • Headset

      Illustration indicating the locations of the charging ports (B) on the left and right headset units

      B: Charging ports of the headset units (left, right)

    • Charging case

      Illustration indicating the locations of the left and right charging ports (C) of the charging case

      C: Charging ports of the charging case (left, right)

    Note

    • Do not use an air duster, etc. to remove dust, etc.
      Dust, etc. may enter the sound output part of the headset, which may lead to malfunction.

    Cleaning the sound output parts

    The sound output part of the headset unit is designed with a mesh-like structure.

    Wipe off any dirt or earwax on the mesh and groove parts of the headset unit with a cloth that has been moistened with water and wrung out well.

    Remove the dirt so that it does not push into the mesh part of the headset unit deeply.

    Illustration indicating the locations of the mesh part (D) and groove (E) on the headset unit

    D: Mesh

    E: Groove

    Cleaning the holes of the charging case

    Clean the holes where the earbud tips fit with a cotton swab, etc.

    Illustration indicating the locations of the left and right holes (F) of the charging case

    F: Holes of the charging case (left, right)

    Drying the headset

    After cleaning is complete, leave the headset to dry thoroughly at room temperature.

    Note

    • When drying the headset, if the IR sensors touch the table, the headset will be considered worn and the rechargeable battery may continue to be consumed. Place the headset units with the IR sensors facing sideways or upwards.
    • The mesh part at the sound output part of the headset unit may peel off or break if it is rubbed forcefully. Do not rub this part with too much force.
  3. Attach the earbud tip.

    Push the earbud tip firmly onto the sound conduit (sound output tube) on the headset so that the earbud tip covers the inner end of the sound conduit. Do not attach the earbud tip in a loose or skewed manner.

    Illustrations indicating how to attach the earbud tip to the headset unit by fitting the protruding part of the headset unit into the recess in the earbud tip

    If the earbud tip is not completely attached, the earbud tip may be removed from the headset and the sound quality, noise canceling effects, and wearability may be impaired.

  4. Set the headset in the charging case.

    After maintenance as well as after cleaning and drying the headset, be sure to set the headset units in the charging case.

    Be sure to close the charging case lid.