List of Supported Functions

The following table shows the supported functions and their corresponding operating conditions.

Operation panel Functions of the unit Operating conditions
IRIS Adjusting the iris manually –
AUTO IRIS Turning Auto Iris on/off –
ND Variable ND mode transmittance adjustment and preset position switching The RCP/MSU filter positions and camera ND filter operation are given below:
ND1: [Clear]
ND2: Variable ND
ND3: [Preset1]
ND4: [Preset2]
ND5: [Preset3]
Transmittance adjustment in variable ND mode must be configured on the RCP/MSU.
MASTER GAIN Adjusting the gain manually (3 dB units) Enabled when both the shooting mode is set to [Custom] mode and [Shooting] – [ISO/Gain] – [Mode] is set to [dB] in the camera menu.
The display value of the dB value of the RCP/MSU is rounded to the closest 3 dB.
WHITE (R/B) Adjusting the white balance ([R Gain] / [B Gain]) manually Enabled when [White Mode] is set to [Memory A (R/B)] or [Memory A (T/T)].
WHITE (Color Temp) Adjusting the white balance (color temperature/tint) manually
  • RCP – [Color Temp]: White balance color temperature
  • RCP – [Balance]: White balance tint value
AWB White balance automatic adjustment –
ATW Turning the ATW (Auto Tracing White Balance) function on/off Enabled when the shooting mode is set to [Custom].
BLACK R/B Adjusting the black balance Enabled when the shooting mode is set to [Custom].
MASTER BLACK Adjusting the master black level
  • Enabled when the shooting mode is set to [Custom].
  • [H/V Ratio] and [Crispening] settings are enabled when [Paint/Look] – [Detail] – [Manual Setting] is set to [On] in the camera menu.
DETAIL
  • Turning the detail function on/off
  • Setting the detail level
  • Setting [H/V Ratio]
  • Setting [Crispening]
User Matrix
  • Turning the user matrix correction function on/off
  • Setting matrix correction values (R-G/R-B/G-R/G-B/B-R/B-G)
Multi Matrix
  • Turning the multi matrix correction function on/off
  • Setting the hue and saturation of the color used for multi matrix correction
  • Turning on/off the display function (Gate function) that distinguishes between the areas corresponding to the colors that are the target of multi matrix correction.

    Note

    • Configurable only when the camera and RCP/MSU are connected in Bridge mode.
Knee Turning the knee correction function on/off
Turning the auto knee function on/off
Setting the knee point and knee slope
BARS Turning color bars on/off

Note

  • Configurable only when the camera and RCP/MSU are connected in Bridge mode.
SHUTTER
  • Turning the shutter function on/off
  • Setting the shutter speed value
    (Turning auto shutter on/off, setting angle shutter, setting slow shutter, and setting ECS not supported.)

    Note

    • The RCP shutter settings may not be displayed depending on the configured shutter speed value.
    • The RCP shutter settings may not be displayed correctly if the shutter cannot be operated from the RCP.
 When auto shutter is on, auto shutter will continue to operate even if you turn the shutter on/off or change the shutter speed value from the RCP.
When the shutter is set to [Angle], turning the shutter on/off or changing the shutter speed setting from the RCP is not supported.
CALL/Tally CALL/Tally function indication Enabled when [Technical] – [Tally] – [Tally Control] is set to [External] in the web menu.

Note

  • After configuring the unit to satisfy the operating conditions of the function you want to use, enable the connection between the unit and the RCP/MSU/CNA-2. If the operating conditions are adjusted after the connection is enabled, unintended behavior may occur.
Go to Page Top
 
TP1001804704