[Audio] Menu

The following tables describe the function and settings of each menu item.

For details about settings, see the following topic.
Block Diagrams

[Audio] – [Audio Rec Format]

Sets audio recording format settings.

Menu item Sub-item setting Factory default value Description
[Audio Rec Format] [48kHz/24bit] / [48kHz/32bit float] / [96kHz/24bit] / [96kHz/32bit float] [48kHz/24bit]

Sets the audio recording format.

Note

  • When set to [48kHz/32bit float] / [96kHz/24bit] / [96kHz/32bit float], connect a supported Multi Interface Shoe compatible accessory and select [Audio] – [Audio Input] – [CH1 Input Select] to [CH4 Input Select] – [Shoe CH1] to [Shoe CH4] in the full menu.

[Audio] – [32bit float WAV Rec]

Sets 32-bit float audio data settings.

Menu item Sub-item setting Factory default value Description
[Setting] [On] / [Off] [Off]

Turns the 32-bit float audio data recording function on/off.

Note

  • When set to [On], connect a supported Multi Interface Shoe compatible accessory and select [Audio] – [Audio Input] – [CH1 Input Select] to [CH4 Input Select] – [Shoe CH1] to [Shoe CH4] in the full menu.

[Audio] – [Audio Input]

Sets audio input settings.

Menu item Sub-item setting Factory default value Description
[CH1 Input Select] [External MIC (L)] / [Internal MIC] / [Shoe CH1] [Internal MIC] Switches the input source for CH1.
[CH2 Input Select] [External MIC (R)] / [Internal MIC] / [Shoe CH2] [Internal MIC] Switches the input source for CH2.
[CH3 Input Select] [External MIC (L)] / [Internal MIC] / [Shoe CH1] / [Shoe CH3] / [Off] [Internal MIC] Switches the input source for CH3.
[CH4 Input Select] [External MIC (R)] / [Internal MIC] / [Shoe CH2] / [Shoe CH4] / [Off] [Internal MIC] Switches the input source for CH4.
[Reference Level] −20dB / −18dB / −16dB / −12dB −20dB Selects the recording level of the 1 kHz reference tone signal.
[CH1 Filter] [Wind Filter] [On] / [Off] [Off] Enables/disables the wind reduction filter for recording CH1.
[Noise Cut Filter] [On] / [Off] [Off] Enables/disables noise reduction for recording CH1.
[Zoom Noise Cut(INT MIC)] [On] / [Off] [Off]

Enables/disables motor noise reduction for the internal microphone during power zoom for recording CH1.

Note

  • Enabled only when [CH1 Input Select] is set to [Internal MIC].
[CH2 Filter] [Wind Filter] [On] / [Off] [Off] Enables/disables the wind reduction filter for recording CH2.
[Noise Cut Filter] [On] / [Off] [Off] Enables/disables noise reduction for recording CH2.
[Zoom Noise Cut(INT MIC)] [On] / [Off] [Off]

Enables/disables motor noise reduction for the internal microphone during power zoom for recording CH2.

Note

  • Enabled only when [CH2 Input Select] is set to [Internal MIC].
[CH3 Filter] [Wind Filter] [On] / [Off] [Off] Enables/disables the wind reduction filter for recording CH3.
[Noise Cut Filter] [On] / [Off] [Off] Enables/disables noise reduction for recording CH3.
[Zoom Noise Cut(INT MIC)] [On] / [Off] [Off]

Enables/disables motor noise reduction for the internal microphone during power zoom for recording CH3.

Note

  • Enabled only when [CH3 Input Select] is set to [Internal MIC].
[CH4 Filter] [Wind Filter] [On] / [Off] [Off] Enables/disables the wind reduction filter for recording CH4.
[Noise Cut Filter] [On] / [Off] [Off] Enables/disables noise reduction for recording CH4.
[Zoom Noise Cut(INT MIC)] [On] / [Off] [Off]

Enables/disables motor noise reduction for the internal microphone during power zoom for recording CH4.

Note

  • Enabled only when [CH4 Input Select] is set to [Internal MIC].
[CH1 Level Control] [Auto] / [Manual] [Auto]

Selects automatic audio input level adjustment or manual adjustment for CH1.

Note

  • If both [CH1 Input Select] / [CH2 Input Select] are set to [Internal MIC], CH2 is switched to automatic/manual in conjunction with this setting.
[CH2 Level Control] [Auto] / [Manual] [Auto]

Selects automatic audio input level adjustment or manual adjustment for CH2.

Note

  • If both [CH1 Input Select] / [CH2 Input Select] are set to [Internal MIC], CH2 is switched to automatic/manual in conjunction with the [CH1 Level Control] setting.
[CH3 Level Control] [Auto] / [Manual] [Auto]

Selects automatic audio input level adjustment or manual adjustment for CH3.

Note

  • If both [CH3 Input Select] / [CH4 Input Select] are set to [Internal MIC], CH4 is switched to automatic/manual in conjunction with this setting.
[CH4 Level Control] [Auto] / [Manual] [Auto]

Selects automatic audio input level adjustment or manual adjustment for CH4.

Note

  • If both [CH3 Input Select] / [CH4 Input Select] are set to [Internal MIC], CH4 is switched to automatic/manual in conjunction with the [CH3 Level Control] setting.
[CH1 Input Level] 0 to 99 49 Sets the input level for CH1.
[CH2 Input Level] 0 to 99 49 Sets the input level for CH2.
[CH3 Input Level] 0 to 99 49 Sets the input level for CH3.
[CH4 Input Level] 0 to 99 49 Sets the input level for CH4.
[Audio Input Level] 0 to 99 99 Sets the audio input level.
Can be used as the master volume, according to the settings of [CH1 Level] to [CH4 Level].
[Limiter Mode] [Off] / −6dB / −9dB / −12dB / −15dB / −17dB [Off] Selects the limiter characteristic for large input signals when adjusting the audio input level manually.
[CH1&2 AGC Mode] [Mono] / [Stereo] [Stereo] Sets the auto level adjustment mode for CH1 and CH2. When [Stereo] is selected, auto gain control is linked between channels.
[CH3&4 AGC Mode] [Mono] / [Stereo] [Stereo] Sets the auto level adjustment mode for CH3 and CH4. When [Stereo] is selected, auto gain control is linked between channels.
[AGC Spec] −6dB / −9dB / −12dB / −15dB / −17dB −6dB Selects the auto gain control characteristic.
[1kHz Tone on Color Bars] [On] / [Off] [Off]

Turns the 1 kHz reference tone signal on/off when displaying color bars.

Note

  • When set to [On], the 1 kHz reference tone signal is output on CH3/CH4, even if [CH3 Input Select] / [CH4 Input Select] are set to [Off].
[CH1 Level] Input without XLR adaptor: [Audio Input Level] / [CH1 Input Level] / [Level+CH1 Input Level]
Input with XLR adaptor: [Audio Input Level] / [Through]		 Input without XLR adaptor: [Level+CH1 Input Level]
Input with XLR adaptor: [Audio Input Level]

Sets the combination of audio input level adjustments enabled for CH1.
[CH2 Level] Input without XLR adaptor: [Audio Input Level] / [CH2 Input Level] / [Level+CH2 Input Level]
Input with XLR adaptor: [Audio Input Level] / [Through]		 Input without XLR adaptor: [Level+CH2 Input Level]
Input with XLR adaptor: [Audio Input Level]

Sets the combination of audio input level adjustments enabled for CH2.
[CH3 Level] Input without XLR adaptor: [Audio Input Level] / [CH3 Input Level] / [Level+CH3 Input Level]
Input with XLR adaptor: [Audio Input Level] / [Through]		 Input without XLR adaptor: [Level+CH3 Input Level]
Input with XLR adaptor: [Audio Input Level]		 Sets the combination of audio input level adjustments enabled for CH3.
[CH4 Level] Input without XLR adaptor: [Audio Input Level] / [CH4 Input Level] / [Level+CH4 Input Level]
Input with XLR adaptor: [Audio Input Level] / [Through]		 Input without XLR adaptor: [Level+CH4 Input Level]
Input with XLR adaptor: [Audio Input Level]		 Sets the combination of audio input level adjustments enabled for CH4.

[Audio] – [Audio Output]

Sets audio output settings.

Menu item Sub-item setting Factory default value Description
[Monitor CH] [CH1/CH2] / [CH3/CH4] / [MIX ALL] / [CH1] / [CH2] / [CH3] / [CH4] [CH1/CH2]

Selects the audio channel output to the headphone connector and built-in speaker.

Note

  • If audio for multiple channels is set for simultaneous output, the output level for each channel is reduced for output to prevent clipping.
[Volume] 0 to 50 0 Adjusts the monitoring audio level of the headphones connector and built-in speaker.
[Headphone Live/Processed] [Live] / [Processed] [Live] Selects whether to output audio to headphones with the fastest possible timing or to output processed audio, such as added noise reduction.
[Headphone Mono/ST] [Mono] / [Stereo] [Stereo] Selects whether the headphone connector output is monaural or stereo.
[Alarm Level] 0 to 7 4 Adjusts the volume of the alarm.
[HDMI Out CH] [CH1/CH2] / [CH3/CH4] [CH1/CH2] Sets the combination of audio channels on the HDMI output.
TP1002215354