Setting the Streaming Format

Set the streaming format using [Stream] > [Stream] > [Stream Setting] > [Setting] in the web menu.

When [Setting] is set to [RTSP]

In RTSP streaming, the image from a single camera can be viewed simultaneously by up to five users.

You can set up to two video codec modes.

Item Description

[Port Number]

Sets the port number to use for RTSP streaming. The default value is 554.
Changing the setting will reboot the RTSP server.

[Time Out]

Specifies the timeout time of the Keep-Alive command for RTSP streaming. The timeout time can be set in the range 0 seconds to 600 seconds. The default value is 60 seconds.
When set to 0 seconds, timeout due to the Keep-Alive command does not occur.

[Authentication]

Sets whether authentication is required.

[Video Port Number 1]
[Video Port Number 2]

Specifies the image data communications port number to use for RTSP unicast streaming. The factory default value for [Video Port Number 1] is 51000. The factory default value for [Video Port Number 2] is 53000. Specify an even number in the range 1024 to 65534. The number set here and the subsequent odd number, obtained by adding 1, become the two port numbers used for image data communications and control.
[Video Port Number 1] and [Video Port Number 2] correspond to [Stream] > [Video Stream] > [Video Stream 1] and [Video Stream 2].

[Audio Port Number]

Specifies the audio data communications port number used for RTSP unicast streaming. The default value is 57000. Specify an even number in the range 1024 to 65534. The number set here and the subsequent odd number, obtained by adding 1, become the two port numbers used for audio data communications and control.

When [Setting] is set to [RTMP]

The video codec mode that can be used for RTMP is H.264 only. To use RTMP, [Stream] > [Audio Stream] must be set to [On] in the web menu.

Item Description

[Server URL]

Sets the upload destination URL. Specify a character string beginning with “rtmp://” or “rtmps://”.

[Stream Key]

Enter the stream key obtained from the site you are using. Pressing the [Clear] button will clear the entry.

Note

  • Exercise caution when handling the stream key. If the stream key is known by a third party, there is a risk of spoofing the stream.

[Root Certificate]

Imports the root certificate required for streaming using the RTMPS protocol. To import the root certificate, press the [Load] button and select a root certificate. Press the [OK] button in the file selection dialog to import the selected file into the unit. If there is an imported root certificate in the unit, the root certificate will be updated. To delete an imported root certificate, press the [Delete] button on the setup screen. The root certificate status is displayed in [Root Certificate Status].

Note

  • Import the root certificate required by the streaming service.

When [Setting] is set to [SRT-Caller] or [SRT-Listener]

The video codec mode is H.264 only.

Item Description

[Destination]

Displayed when the streaming mode is set to [SRT-Caller]. Sets the connection destination URL.

[Port Number]

Displayed when the streaming mode is set to [SRT-Listener]. Sets the port number on which to listen. The default value is 4201.

[Latency]

Sets the latency in the range 20 ms to 8000 ms. The default value is 120.

[TTL]

Sets the TTL value in the range 1 to 255. The default value is 64.

[Encryption]

Selects the encryption method. Select Off, AES128, or AES256. The default value is Off.

[Passphrase]

Sets the passphrase used for encryption. Pressing the [Clear] button will reset the configured passphrase.

[ARC]

To enable the Adaptive Rate Control function, set to On.
When the Adaptive Rate Control function is enabled, interruptions in the image caused by communication line congestion can be reduced.

When [Setting] is set to [NDI|HX]

An NDI|HX license is pre-installed in software version 3.00 and later.

Note

  • The unit complies with NDI® HX2 by Vizrt NDI AB.
  • The unit can send video to NDI® HX2 compatible software applications and hardware over the network.
Item Description

[License]

Displays the license information.

[Source Name]

Displays the source name.

[Group]

To enable the NDI grouping function, set to On.
[Group Name]: Sets the NDI group name. Multiple settings can be configured separated by a comma.

[Discovery Server 1]
[Discovery Server 2]

Sets NDI discovery server 1 and NDI discovery server 2.

[Reliable UDP Mode]

To enable Reliable UDP mode, set to On.

[Multicast Mode]

To enable multicast streaming, set to On.
[Multicast Prefix]: Sets the prefix to use for multicast streaming.
[Multicast Netmask]: Sets the netmask that determines the multicast address range.
[Multicast TTL]: Sets the TTL value for multicast streaming in the range 1 to 256. The default value is 3.

[Multi-TCP Mode]

To enable Multi-TCP mode, set to On.

[Unicast UDP Mode]

To enable Unicast UDP mode, set to On.

About 3rd-party services and software

Different terms of use may apply.

  • The provision of services and software updates may be interrupted or terminated without notice.
  • The description of services and software is subject to change without notice.
  • Separate registration and subscription may be required.

Sony will not be liable for any claims made by users or a third party due to the use of services and software of other companies.

Go to Page Top